This is the operator’s manual for the John Deere 14T automatic pickup baler, contains information lubrication, operation, maintenance, and assembly. This is. This is the parts catalog for the John Deere 14 Twin Baler. This manual has exploded views of all the parts of the 14 series baler. An absolute must if you are . THIS IS A MANUAL PRODUCED BY JENSALES INC. JOHN DEERE AND IT’S SUCCESSORS John Deere 14T Automatic Baler with Power Take-Off.

Author: Vudolrajas Dushicage
Country: Argentina
Language: English (Spanish)
Genre: Career
Published (Last): 25 May 2013
Pages: 336
PDF File Size: 4.8 Mb
ePub File Size: 9.35 Mb
ISBN: 226-6-38964-336-2
Downloads: 13688
Price: Free* [*Free Regsitration Required]
Uploader: Nigrel

As you roll it over by hand, check to see that all actions happen at about the same time. There is no “I” in team, but there is a “Me” if you want to jumble it up a bit Page 1 of 2 1 2 Last Jump to page: There is a spring force setting here, too. The time now is Does the twine get pulled out of the twine disk not enough tension. Since adjusting the tucker finger, it’s baling like crazy. Originally Posted by Mike It has no problem with the baler.

I presume that the sisal you are using is good square bale twine. Note that this conversion goes the other way. Thickness has no real bearing on its operation other than the stuff has to pass thru the needle eyes and the billhook tongue.

We will not share your e-mail address with any other party for any reason.


John Deere 14t Baler Operators Manual OME16470

You need fish scale to measure it 15lbs Do you have it threaded properly? Is the billhook tongue opening to receive the knot parts? Have you checked my knotter video on YouTube?

Slippery twine needs more clamping force. If they are good, then start looking at spring tensions: Thanks for the replies! Is there a lot of dirt around the hay dogs in the bottom of the bale case.

John Deere 14T baler prob What kind of twine are you using? Second is at the twine disk.

Member Log In

Is the billhook revolving? Thread Tools Show Printable Version. Are there sharp edges or nicks in the twine disk that may be cutting the twine instead of it being held onto? Anyway, the problem is, our baler will not tie one side.

John Deere 14T baler prob We use the old fashion sisal twine Yes you can thread round bale plastic twine and make it work.

If not Check the manual. Tucker fingers are the usuall culprit. By clicking the button below, you agree to the TractorByNet. That’s all I use in my 14t. It only jogn the sisal twine. Other trademarks on this page are the property of their respective owners. Keep the conversation going until it gets working.

What kind of twine are you using? This is the force necessary to hold the twine in the disk. All times are GMT Gulliver is a bit far for a road trip, but you never know John Deere 14T baler prob.


Oh yea, I know Brighton is a ways, I’ve been there. No reason that plastic twine won’t work.

John Deere 14T Baler – Parts Catalog | Farm Manuals Fast

And does it hold the twine when it revolves? Secondly, go easy on me, I’m a gal!!!

My old Dere baler chokes on the new stuff. I know haying isn’t 14 to be that much work! There are 2 adjustments that must be made. Last year, it tied pretty decent, out of 10 bales, maybe 1 wouldn’t tie. Kohn it works pretty darn good on the ‘ weight. I was gone to Little League finals and when I came home, it was working. The pull tension is adjusted by turning down the springs on the clamps. The old balers don’t seem to like the new poly twine as it’s too slick.

However, twine pulling of the billhook sounds like a twine disk problem: Try reversing the twine bales and see if the problem moves to the other knotter. By that I mean: Are the needles placing the twine properly in the twine disk?